|
|
|
|
|
|
|
Enter a product number or part of its description below...
OR
Now choose a product sub group (if any are present below)
| 18 Items Returned | Go To Page: | 1 |
|
| | | Stock Number | Product | Sub Group | Capacity | Description |
|
|
| 47096 | KILN/CALCINER | | 24021 | 24" ID x 21' long, Bartlett Snow 304SS indirect fired rotary calciner. Has 15'6" heating area and 5'6" cooling section. Gas fired from underneath calciner tube. One section has (3) gas burners w/Pedcock feeders every 6"; 2nd section has (2) gas burners w/Pedcock feeders every 6". (63) total feeders. Burners run parallel to length of calciner. Tube has internal flights. Brick lined external shell. Mtd on (2) tires w/trunnions and driven by Girth gear w/chain to gearhead motor, 2 HP, 3/60/230/460 volt motor, 25 rpm output. Skid mtd design w/feed and discharge hoods. Mtd on skid is Nash L2 vac pump, direct driven by 5 HP, 3/60/220/440 volt motor. |
|
|
| 73480 | KILN/CALCINER | | 1X026 | UNUSED 18.4" (460mm) dia x 26'3" (8000mm) long nickel (2.4068) calciner. Mfd by Plant and Equipment Eng (Germany), SN A27146, Type AG22/11/DK94-241, blt 1988. Heating zone 24" (600mm) wide, cooling zone 17'9" (5400mm) long. Tube driven by 1.5 KW, 3/50/380 volt motor. Calciner is electrically heated within a brick housing. Maximal allowable temps are: for the outer walls of the tube heating body 1652 deg F (900 deg C), for the heating chamber 1472 deg F (800 deg C), for the tube 752 deg F to 842 deg F (400 deg C to 450 deg C). Electrical heating capacity 5 KW. Tube speed 1-5 rpm. |
|
|
| 83298 | KILN/CALCINER | | 99086 | 12'3" (3.74 meter) OD, (9'10" (3 meter) inside refractory) x 86' (26.3 meter) long CS direct fired rotary kiln. Rated capacity 3,300 ton/yr. Mfd by Babcock Krauss-Maffei. Temp 1200 deg C - 1300 deg C. Shell thickness 20mm, 114mm thick heat insulation lining and 250mm thick refractory. SS lifters and cast refractory lifters. Dual fuel (natural gas/oil) direct fired burners. Girth gear driven by variable speed drive, 1.48 rpm max. Unit has air driven emergency drive, .145 rpm max. Air supplied by diesel engine driven compressor. Kiln equipped w/on-board control panel used to sequence the actuation of the air injection valves and control the fans. Gas consumption kiln 6.6 cu meters/S, afterburner 3.8 cu meter/S. Steam fed via rotary coupling to manifolds mtd on outside of kiln shell and feed end. Controlled by remote operated valves which supply (7) zones along axis of shell. |
|
|
| 100191 | KILN/CALCINER | | 36034 | 36" x 34', 316SS indirect fired calciner. Mfd by Industrial Furnace/Finch Mfg, Type reverse retort. 4-zone heating. Electrically heated. 3/60/480 volt. Electrical heating input 348 KW, max temp 1000 deg F. Octagonal shell. 3/8" wall thickness. Driven by TB Woods 5 HP DC adjustable speed motor thru gear reducer. Shell speed 0-5 rpm. Tire and trunnion mtd. W/feed and discharge assemblies. |
|
|
| 100192 | KILN/CALCINER | | 36034 | 36" x 34', 316SS indirect fired calciner. Mfd by Industrial Furnace/Finch Mfg, Type reverse retort. 2.6MM BTU/hr input. 1300 deg F max temp. 4-zone heating. Gas fired Eclipse burner. Hexagonal shell. Tire and trunnion mtd. Shell driven by TB Woods 5 HP DC adjustable speed motor thru gear reducer. Screw feed driven by TB Woods 1 HP DC motor thru Dodge reducer w/SCR drive. W/Eclipse 7 1/2 HP blower, 70500 cfh. |
|
|
| 107682 | KILN/CALCINER | | 18016 | 18" diameter x 16'8" long. 316LSS Renneburg Model #P77-106 rotary calciner. Has 6' long heating section and 5'6" long cooling section. Electric heated with tubular heating bars. Tire and trunnion mounted. Chain and sprocket driven by 3 HP, 3/60, 1750 rpm motor thru Cone 30:1 ratio right angle gear reducer. Has (2) 2,000 cfm @ 70 degree F exhaust fans, rated 2028 rpm, 3.57 brake HP. |
|
|
| 107686 | KILN/CALCINER | | 36040 | 36" diameter x 40' long Bartlett Snow rotary calciner. Serial #81100. 316SS contacts. Indirect fired, Has (4) heating zones as follows: 7' long (65 KW), 9' long (25 KW), 6' long (25 KW), and 6' long (12 KW). 8' long cooling zone with external water spray nozzles. 40' is the overall cylinder length. 1st zone is for drying at 150-200 degree C; 9' zone is for heating at 350-360 degree C; the last 2-zones are for calcining at 350-360 degree C. Tire and trunnions mounted. Chain and sprocket driven. |
|
|
| 110548 | KILN/CALCINER | | 14026 | 14" diameter x 26' long indirect fired, electrically heated, high nickel/Inconel tube calciner. Manufactured by CE Raymond, Serial #85051, Type #T50514, built 1986. 1800 degree F max. 12' long 4-zone heating section. Tire and trunnion mounted on (2) 10" diameter x 6" face tires and (2) 10" diameter x 4" face tires. Cylinder chain and sprocket driven by Reeves motodrive, 3 HP, 3/60/230/460 volt, 1800 rpm TEFC motor. Size 243, Z-configuration. Rated 4.85 to 48.5 output rpm. Has 316SS agitated screw feeder 3' long x 20" deep. Agitator and screw driven by 1/2 HP, 3/60/230/460 volt, 1800 rpm TEFC Reeves motordrive. Size 053. 8/4 to 84 rpm output. Has 3' cooling section with schedule 40 galvanized steel manifold and (3) full jet nozzles 3/8 G22. Discharge end of calciner has rotary airlock valve, manufactured by Prater Model #PAV-6-C, chain driven by 1/2 HP, 3/60/230/460 volt, 1800 rpm TEFC motor. 29 rpm output. |
|
|
| 201362 | KILN/CALCINER | | 09006 | 9" diameter x 6'6" indirect fired, electrically heated, skid mounted, rotary calciner. Manufactured by Heyl & Patterson, type 44RO-867-21S, serial number 888856-L. Rated 56.6 kW 3/60/108/60.5V. Maximum allowable temperature: 2100 degrees F. Electrical heating in four zones. With Water cooling box at discharge end . Equipped with gravity feed hopper to retort with variable speed screw feeder. Gravity discharge. Dryer's pitch is adjustable via mechanical weight adjustment. With two controls, dry type transformers( one for each zone). Tube is 310 s/s.
Inlet Hood & outlet hood are 316ss. |
|
|
| 201408 | KILN/CALCINER | | 72068 | 6' diameter x 68' long 316SS indirect fired rotary calciner, Manufactured by Bartlet Snow Division of CE Raymond. Shell equipped with internal lifters for lifting product as drum rotates.
Maximum operating temperature: 800 degrees F. Furnace duty: 1400 KW in three heat zones. Dryer is equipped with variable speed drive, hydraulically operated cylinder tilting system. Driven by GE 75 HP 3/60/230/460 V motor. With screw feeder. Electrically heated. With controls and transformers included. Calciner was only operated less than six months. Previous Use Polymer drying. |
|
|
| 201841 | KILN/CALCINER | | 72059 | 6' diameter x 59' long over all length molecular sieve rotary calciner, 1500 deg F. Furnace area 6' diameter X 32' long, cooler area 6' diameter X 13'6" long. Calciner shell & Cooler shell 3/8" thick 309SS. Feed end dam ring 1/4" thick 304SS. The reinforcing bands for the tires and girth sprocket is mfd of 3/8" thick 304SS. The tires are composed of (2) two 84" O.D. X 5" face X 75" I.D. rings CS. The trunnions are 16" diameter X 7" face at the drive end and 16" diameter X 12" face att the floating discharge end, Timken roller bearing on steel shafts with cover plates, seals, shims and gudgeons. Chain Drive consists of, 20 HP, 1750 RPM, TEFC Electric Motor, Dodge para flex coupling, Dodge TCR6 Maxum Class II concentric reducer with extended input shaft to connect to auxiliary drive. Allen Bradley 1335 Plus AC variable frequency inverter with control panel and all SS NEMA 4X enclosure. Indirect fired, with North American natural gas burners (3) zones each consisting of Model 4442-4 North American Burners rated at 540,000 BTU/hr each, there are 4 burners/zone, all zones have 10:1 turndown, each burner to be pilot ingnited and monitored with weather resistant ultraviolet detectors. |
|
|
| 204598 | KILN/CALCINER | | 24016 | 24" dia x 16' long Elino Rotary Calciner. 4 zone indirect fired natural gas by Krom/Schroder 110V 50Hz. Chamber is 5' OD. Cyclinder is chain and sproket driven by 22 kw, 50Hz, 380 volt, 1422 rpm motor. Tire and Trunnion mounted. Blower motor 575 volts. 310 s/s |
|
|
| 207269 | KILN/CALCINER | | 01006 | 6" ID diameter x 72" long Barlett-Snow Calciner, 1200 degrees F, with HH Alloy Tube, Manufactured by Bartlett-Snow-Pacific, Serial Number K5334. Skid mounted with the following overall dimensions: Length, 123" X width, 48" X height, 64". Heating area is 36" long with 4" insulation pack. Gas manifold contains seven jets, and is fed by a 3/4" inlet line. Heating chamber is exhausted by a 1 hp exhaust fan. Product hoppers and screw feed are 316 SS, inlet hopper is 8.5" X 11". Screw feed is 2" and driven by a 1/2 hp Browning motor. Calciner drive is by Seimens, 1750 rpm, and 2 hp. |
|
|
| 212059 | KILN/CALCINER | | 0 | 14"wide x 250' long Nickel/Chrome Mesh belt, single file gas fired proheat Kiln with cooling section. Mfg by: Cobel Comes S.A (Belgium), Serial #F3927, Material: 37% Nickel, 18% Chrome. 9" to 35'ft/Min belt speed, 63.5 long Kiln section, steel casing lined with refractories, 43'long, cooling section, combined length 106', operation temp, 850 degrees C, Natural gas/air fired burners, 5 Psi gas supply, direct fired, 5 heating zones, 30 burners (15 per side), Stordy Hauck wall burners, air cooling by Woods, 4 stage airofoil fan, 30"impeller, 50 hp motor, 26,500 cfm at 30" water guard. |
|
|
| 704184 | KILN/CALCINER | | 1020 | 1' (304mm) ID x 20' (6087mm) direct gas fired CS rotary kiln. CS housing w/brick lining. Unit bull gear driven by 5.5 KW, 3/50/415 volt, 940 rpm non-flameproof motor via 49.2:1 ratio Renold gearbox. Unit with 6 1/2" dia x 52" long SS screw feeder, chain driven by .37 KW non-flameproof motor via 30.75:1 ratio reduction gearbox. Unit also w/(1) CS 7.5 KW fan; (1) 22" dia x 33" str side SS feed hopper w/fan; (1) 16" dia x 106" str side SS gas scrubber. Unit mtd on (2) trunnions. |
|
|
| 705341 | KILN/CALCINER | | 1012 | 1'8" (530mm) inner diameter x 12'5" (3800mm) long, direct gas fired 304LSS rotary kiln. Manufactured by Nesa. Working capacity 500 kg/hr @ 850 degree C. Gas flow 250,000 Kcal/hr. 304LSS total length 15'9" (4800mm), 2'8" (810mm) outer diameter chamber with refractory brick lining. Unit bull gear driven by 0.5 - 5 rpm drive. Unit complete with 304LSS cyclone, (1) fan. Mounted on (2) trunnions. |
|
|
| 706261 | KILN/CALCINER | | 1026 | 600mm inner diameter x 8.2m long high Nickel/Chrome indirect gas fired Calciner with 2-heating zones, manufactured by Selas, approx production capacity 300 kg/hr, max product temperature 1050-1150 deg C, material of feed & discharge sections Z15.CN.20/10, material of middle section Z12.NC.35/25, heating length 4.1m long, 33-gas burners, drum 630mm O/D, drum chain driven by Leroy Somer geared motor with 5.5 kw, 3/50/220-380 volt, 1435 rpm motor with type CB-E2-SB3, 31.8:1 ratio reduction gearbox, drum speed 1.25-10 rpm, drum with angle adjustment mechanism, drum mounted on 2-sets of 760mm diameter trunnion wheels, thrust bearings on drum tyres, drum with hammers, drum enclosed with steel outer casing insulated with shaped ceramic blocks, feed chute, gas regulation system for temperature control and automatic cut off, unit all mounted on c/steel frame,
Calciner with (1) c/steel inclined discharge water cooled screw conveyor/cooler, 200mm wide x 4m long x 300mm deep, driven by Leroy Somer geared motor with 1.1 kw, 3/50/220-240-380-415 volt, 1420 rpm motor with a type CB-2504-SB3, 364.8:1 ratio gearbox, (1) ABB Solyvent-Ventec fan, type HD-73H-RO-ARGT-4-RT-12, driven by 11 kw, 3/50/380-415 volt, 2930-2945 rpm motor,
|
|
|
| 706262 | KILN/CALCINER | | 1026 | 600mm inner diameter x 8.2m long high Nickel/Chrome indirect gas fired Calciner with 2-heating zones, manufactured by Selas, approx production capacity 300 kg/hr, max product temperature 1050-1150 deg C, material of feed & discharge sections Z15.CN.20/10, material of middle section Z12.NC.35/25, heating length 4.1m long, 33-gas burners, drum 630mm O/D, drum chain driven by Leroy Somer geared motor with 2.2 kw, 3/50/220-380 volt, 1420-1435 rpm motor with type CB-2402-SB3, 31.5:1 ratio reduction gearbox, drum speed 1.25-10 rpm, drum with angle adjustment mechanism, drum mounted on 2-sets of 760mm diameter trunnion wheels, thrust bearings on drum tyres, drum with hammers, drum enclosed with steel outer casing insulated with shaped ceramic blocks, feed chute, gas regulation system for temperature control and automatic cut off, unit all mounted on c/steel frame,
Calciner with (1) c/steel inclined discharge water cooled screw conveyor/cooler, 200mm wide x 4m long x 300mm deep, driven by Leroy Somer geared motor with 1.1 kw, 3/50/220-240-380-415 volt, 1420 rpm motor with a type CB-2504-SB3, 364.8:1 ratio gearbox, (1) ABB Solyvent-Ventec fan, type HD-73H-RO-ARGT-4-RT-12, driven by 11 kw, 3/50/380-415 volt, 2930-2945 rpm motor,
|
|
|
|
|
|
|
|