 |
|
Need Help? or
Have something for sale? USE THIS FORM:
|
|
|
|
|
|
|
|
Chillers
|
 |
|
|
|
207432
125 Ton , Zero Degree Glycol chiller, Manufactured by FES, model # 19ME. Serial # 94623042. Chiller use's 1250 lbs. of R-22 refrigerent. Skid mounted with FES digital micro control panel. Compressor is by FES and exchangers are by FES, and Thermo Power-York. National Board # 9177, MAWP is 300 psi at 400 degrees F, MDMT is -20 at 300 degrees F. Compresssor driven by a 300 hp, 4160 volt, 3575 rpm motor.Glycol Flow= 500 GPM, colling water flow= 500 gpm, Inlet temp.= 10-15 degrees F. Outlet temp. is delta 10 Degrees F.
Read More...
|
| |
|
|
|
|
|
|
|
|
|
|
Enter a product number or part of its description below and click SEARCH
OR
Now choose a product sub group (if any are present below)
| 23 Items Returned | Go To Page: | 1 | 2 |
|
| | | Stock Number | Product | Sub Group | Capacity | Description |
|
|
| 6288 | PRESS | | 50 | M & N Model 0326 compression molding press. 50 ton capacity. 2,000 psi operating pressure, up moving ram, 8" stroke, 14" x 14" plateau. |
|
|
| 6290 | PRESS | | 50 | M & N Model 0326 compression molding press. 25 ton capacity. 2,500 psi operating pressure, up moving ram, 8" stroke, 12" x 12" plateau. |
|
|
| 12789 | PRESS | DEWATERING | 0 | Series B, Beloit/Jones 304SS vert P150 "Pressmaster" dewatering press. 36" dia x 56" long. Mdl 2919, SN 442. Press spindle 2.6 to 20.3 rpm. 16" top opening. Belt driven by 15 HP motor. Mtd on base. |
|
|
| 25807 | PRESS | DEWATERING | | ****Davenport press. Mdl 1-A, SN 183. 12" x 18" feed spout, 6" x 30" discharge. CS/304SS lined. Direct coupled to gear reducer, Jones DH-120, ratio 20.8, rpm 1200. Coupled to Reeves variable speed reducer. Belt driven by 7 1/2 HP, 3 phase, 60 cycle, 1165 rpm, 220/440 volt, Type AA induction motor. |
|
|
| 29742 | PRESS | DEWATERING | | ****Heavy duty vert pulp press, 304SS wetted parts. Mfd by SMA, Mdl 1273DO-E. Screw press widest dia 1200mm (48"), screw sieve housing 1570mm dia. Screw length 2550mm. W/(2) inlets 300mm x 300mm wide. Discharge opening 268mm x 340mm. Press driven by (2) motors coupled to a single planetary gear drive. Press housing bolted into (2) sections. |
|
|
| 29743 | PRESS | DEWATERING | | ****Heavy duty vert pulp press, 304SS wetted parts. Mfd by SMA, Mdl 1273DO-E. Screw press widest dia 1200mm (48"), screw sieve housing 1570mm dia. Screw length 2550mm. W/(2) inlets 300mm x 300mm wide. Discharge opening 268mm x 340mm. Press driven by (2) motors coupled to a single planetary gear drive. Press housing bolted into (2) sections. |
|
|
| 34184 | PRESS | | | 2,000 ton Lake Erie upmoving hydraulic press. (12) 4" openings. (4) post construction, each 13 1/2" dia. 48" stroke on (2) 32" dia rams w/int (2) 6 1/2" dia jack rams. Daylight opening 87" high w/out platens. Platens size 86" x 38", between posts is 92", bed area is approx 38". Speed IPM 248/105/250. (2) 8" prefill valves. Remote controlled. Oil Gear pump DX100-25, driven by 35 HP Westinghouse open frame motor. Manual load and unload elevator. |
|
|
| 43612 | PRESS | DEWATERING | | Infilco/Egremont belt press. Mdl F5008. CS construction. 2 HP, 180 volt DC drive. Control panel. 3.0 meter belt. Chain and sprocket driven by 2 HP, 3/60/180 volt, 1750/2050 rpm. Complete w/valves and gauges. |
|
|
| 43613 | PRESS | DEWATERING | | Infilco/Egremont belt press. Mdl F5008. CS construction. 2 HP, 180 volt DC drive. Control panel. 3.0 meter belt. Chain and sprocket driven by 2 HP, 3/60/180 volt, 1750/2050 rpm. Complete w/valves and gauges. |
|
|
| 44433 | PRESS | | | 40,000 lb ram, Mdl PW225C Pasadena hydraulic press. SN 80-10-008-4407. 12 1/2" x 9 1/2" platen. 1500 watts per platen, 600 deg F max temp, 8 deg/min heat rise. 4" dia ram x 4" stroke, 4-8" daylight, 3-20 tons pressure. |
|
|
| 44454 | PRESS | | | Lab double wire press. |
|
|
| 46327 | PRESS | | | Benchmaster 2-ton punch press. Mdl 132, SN 65287. Punching out various shapes from a variety of materials. Consists of press frame, ram and adjustable ram guides, connecting rod and ball screw, press shaft, eccentric and shaft bearings. Mech full revolution clutch and trip linkage. Drum brake. 1" stroke, shot height 4 3/4". |
|
|
| 85673 | PRESS | DEWATERING | | 2.5 sq meter CS/plastic coated belt filter press. Mfd by Roediger Ecopress, SN 25-234, Type SSP25-3, blt 1986. Belt steering is by rubber coated rollers, pivoted one end, air operated cylinder on the other end. Pneumatic belt tensioning. Sludge cake is distributed by applicator blade from 3/8" to 1 1/16" thick cake. Unti has belt washing and prewashing drum. Driven by Eurodrive 475/2275 volt. Design capacity is 6% dry solids, 3000 lbs DS/hr, 92% capture rate, 100 gpm, 22% sludge cake. |
|
|
| 92393 | PRESS | DEWATERING | | 2 meter Parkson 304SS belt dewatering press. Series 1000, Mdl 2.0, SN MP298. 2 meters (80") of nominal belt width. W/epoxy coated frames, 304SS drums, rolls, drainage troughs, and cloth wash boxes. Unit has an inclined gravity dewatering zone, wedge zone and pressure zone. Belt drive is 5 HP Eurodrive, variable speed complete with 1 1/2 HP variable speed mixer suspended in 300 gal floc tank. |
|
|
| 92394 | PRESS | DEWATERING | | 2 meter Parkson 304SS belt dewatering press. Series 1000, Mdl 2.0, SN MP298. 2 meters (80") of nominal belt width. W/epoxy coated frames, 304SS drums, rolls, drainage troughs, and cloth wash boxes. Unit has an inclined gravity dewatering zone, wedge zone and pressure zone. Belt drive is 5 HP Eurodrive, variable speed complete with 1 1/2 HP variable speed mixer suspended in 300 gal floc tank. |
|
|
| 94707 | PRESS | DEWATERING | | Robbins and Meyers 2.2 meter belt filter press. W/7.5 HP Eurodrive variable speed belt drive. 304SS perforated drum, 304SS cloth wash boxes w/brush cleanable showers, 304SS drainage troughs, hydraulic steering and tensioning. |
|
|
| 94708 | PRESS | DEWATERING | | Robbins and Meyers 2.2 meter belt filter press. W/7.5 HP Eurodrive variable speed belt drive. 304SS perforated drum, 304S cloth wash boxes w/brush cleanable showers, 304SS drainage troughs, hydraulic steering and tensioning. |
|
|
| 106371 | PRESS | DEWATERING | | ****250 sq ft Passavant filters, Mdl 200, vac belt filter/press. CS contact parts. Belt width 78 3/4" wide. Effective filter belt length 41'4". SS belt with rubber rolls, polypropylene collection pans. 3 HP varispeed (DC) drive. Includes starter box. Unit is a continuous sludge dewatering belt w/vac section and a pressing area where the sludge is compressed for final dewatering. |
|
|
| 108333 | PRESS | DEWATERING | | 50 sq. ft. Envirex 3500 dewatering belt filter press. 24" wide belt. Manual tension adjustment. Brush type belt cleaner. Knife discharge. Hydraulic tension adjustment on feed belt. Hydraulic driven by 7 1/2 hp Packer hydraulic drive, Model# PAVC-33-R-223. 300 psi max., 230/460 volt, 1725 rpm explosion proof motor. |
|
|
| 108334 | PRESS | DEWATERING | | 50 sq. ft. Envirex 3500 dewatering belt press. 24" wide belt. Manual tension adjustment, brush type belt cleaner. Knife discharge. Hydraulic tension adjustment on feed belt. Hydraulic driven by 7 1/2 hp Parker hydraulic drive, Model# PAVC-33-R-223, 300 psi max., 230/460 volt, 1725 rpm explosion proof motor. |
| 23 Items Returned | Go To Page: | 1 | 2 |
|
|
|
|
|
IPP Sales Contacts
|
|
|
Keith West
Global Sales
KeithW@ippe.com
+1 609 838 5931 | Amanda Vagell
Global Sales
AmandaV@ippe.com
+1 609 838 5929 | Patti Buchman
Global Sales
PattiB@ippe.com
+1 609 838 5928 | Ray Wagner
Global Sales
RayW@ippe.com
+1 609 838 6043 | Regina Zarmer
Europe Sales & Acquisitions
ReginaZ@ippe.com
+49-306-594-2445 Office
+49-172-313-8439 Mobile
+49-30-6594-2448 Fax | Jo Petrie, Sales Engineer
UK, Scandinavia, Spain, & So.Africa
jop@ippe.com
+44 (0)1642 367 910 Office
+44 (0)1642 367 913 Direct
+44 (0)7770 748884 Mobile
+44 (0)1642 367 920 Fax | Bohumil Cuta,
E. Europe
Sales & Acquisitions
BohumilC@ippe.com
+42-054-821-6680 Office
+42-060-273-7517 Mobile
+420-5-481-22240 Fax | Elisa Lucumi
Central &
So. America Sales
ElisaL@ippe.com
+1 609 838 5927
|
|
|
|
|
|
|
|