|
|
|
|
|
|
|
Enter a product number or part of its description below...
Finally, you may filter the results based on capacity below
| 92 Items Returned | Go To Page: | 1 | 2 | 3 | 4 | 5 |
|
| | | Stock Number | Product | Sub Group | Capacity | Description |
|
|
| 10459 | PULVERIZER | CARBON STEEL | 30 | 30 HP Raymond No. 1 CS screen mill/hammer mill with CS hammers. Belt driven by General Electric 30 HP, 3/60/220/440 volts, 1770 rpm TEFC motor with belt guard. SN 61084. CS screen with 3/4" round perforated holes. Shick rotary valve inlet, T228-1, 6" CS blades, driven by General Electric 1/2 HP, 1725 rpm drip-proof motor with Winsmith speed reducer, Model 6978, SN B6978-6, ratio 58:1. 3/60/230/460 volt w/belt guard. Mill outlet 21" dia chute. Approx mill speed 2100 rpm. Unit on (4) CS legs. |
|
|
| 19180 | PULVERIZER | CARBON STEEL | 20 | 24" dia Sprout Waldron CS double disc attrition mill. Dual drive w/(2) 20 HP, 220 volt open motors, 1740 rpm. |
|
|
| 19346 | PULVERIZER | CARBON STEEL | 5 | 5 HP, CS entoleter mill. Model EIM, SN 5291. Pulverizer driven by by 5 HP, 3/60 motor. Mounted on stand with starter. |
|
|
| 19820 | PULVERIZER | CARBON STEEL | 40 | Mdl UT32, Bauermeister cast iron turbo mill. SN 104475. The stationary grinding element has (6) grinding jaws and (6) seive plates. 1.00mm x 15mm seive perforations, 23" dia (600mm) grinding chamber. 3650 rpm max mill speed, 120 meters/second turbo tip speed. Mill has 1/4 HP vibratory feeder w/magnetic separator in feed chute. Feed chute feeds material directly into mill center. Rotor is belt driven by 40 HP, 3/60/230/460 volt, 1765 rpm TEFC motor. |
|
|
| 19822 | PULVERIZER | CARBON STEEL | 25 | Bauermeister Mdl UT22 pulverizer. SN 33766. The stationary grinding element equipped w/(6) grinding jaws and (6) seive plates. 18" dia (450MM) grinding chamber. 4920 rpm max mill speed. 120 meters/sec turbo tip speed. Mill has vibratory feeder w/magnetic separator in feed chute. Feed chute feeds material directly into mill center. Rotor is belt driven by 25 HP, 3/60/230/460 volt TEFC motor. |
|
|
| 21542 | PULVERIZER | CARBON STEEL | 10 | 10 HP, Raymond CS vert hammer mill system. SN 49129. Will pulverize fineness to 95-99% finer than 5-10 microns. Belt driven by 10 HP, 3/60/230/460 volt, 3500 rpm, 215T Frame, TEFC motor. Unit screw feed hopper w/fractional HP drive. Compact design. |
|
|
| 21884 | PULVERIZER | CARBON STEEL | | CS housing for Type EIM entoleter mill. SN 4905. Mounted on stand. |
|
|
| 23468 | PULVERIZER | CARBON STEEL | 20 | 20 HP, Mdl 6MA, CS Micro atomizer. SN 10868. CS housing, SS fan blades. Rubber hose discharge manifold. 20 HP main drive, 3/60/220/440 volt, 3550 rpm open motor. |
|
|
| 23872 | PULVERIZER | CARBON STEEL | 700 | ****700 HP Pennsylvania CS reversible hammer mill. Mdl SXCAG-119, SN 2767. Rated for 700 HP. Max capacity 435 tons/hr. Feed opening is 6'5" wide, discharge opening is 7'2" wide. Unit has (4) rows of swing hammers. Housing has int breaker blocks for primary breaking and int screen bars for fine crushing. Unit has adjustable dust gate to minimize dust. Requires motor. Unit will crush 2" piece down to 1/4" piece. |
|
|
| 25408 | PULVERIZER | CARBON STEEL | 5 | 5 HP Dorr Oliver CS Dorrco Sulzer disintegrator. (Low lift, axial flow pump). Designed for maceration of primary sewage sludge. 1/3 to 1/2 gpm @ 15 psi +/- 5 psi. 3-bladed cast steel cutting impellor w/stellite inserts. Stationary knife w/stellite inserts. Bronze bearings are water lubricated. Instrument package w/flow switch, pressure switch and screen automatic reverse on blockage or shutdown. Skid mtd. |
|
|
| 25409 | PULVERIZER | CARBON STEEL | 5 | 5 HP Dorr Oliver CS Dorrco Sulzer disintegrator. (Low lift, axial flow pump). Designed for maceration of primary sewage sludge. 1/3 to 1/2 gpm @ 15 psi +/- 5 psi. 3-bladed cast steel cutting impellor w/stellite inserts. Stationary knife w/stellite inserts. Bronze bearings are water lubricated. Instrument package w/flow switch, pressure switch and screen automatic reverse on blockage or shutdown. Skid mtd. |
|
|
| 25487 | PULVERIZER | CARBON STEEL | 8 | 7 1/2 HP, CS Duplex pulverizer mill. Mfd by Duplex Mill & Mfg Co, Mdl MG, SN 67368. (4) rows of 12-1/8" wide CS swing bars. 15" x 6" feed throat w/30" high extension neck. 15" x 13 1/2" mill chamber. 12" dia btm discharge w/32" clearance from base. Rotor driven by 7 1/2 HP, 3/60/230/460 volt, 1745 rpm TEFC mtr thru belts and sheaves. |
|
|
| 28752 | PULVERIZER | CARBON STEEL | 20 | 6MA atomizer. Ni-resist CS. Mfd by Mikro Pulverizing Mach, SN 65-B-583. Has 1/2 HP, 3/60/220/440 volt, UL label motor feed screw. 20 HP, 3/60/220/440 volt, 3600 rpm TEFC main drive motor. |
|
|
| 29218 | PULVERIZER | CARBON STEEL | 10 | Jacobson CS pulverizer and flake breaker. SN 39948. Grinder is 10 HP, 3/60/230/460 volt, 1750 rpm. 6" x 36" side feed, perforated screen, replaceable knives, extra screens and rotors. Flake breaker is Mdl 36, 7.5 HP, 3/60/230/460 volt, 1750 rpm. |
|
|
| 29219 | PULVERIZER | CARBON STEEL | 10 | Jacobson CS pulverizer and flake breaker. SN 31910. Grinder is 10 HP, 3/60/230/460 volt, 1750 rpm. 6" x 36" side feed, perforated screen, replaceable knives, extra screens and rotors. Flake breaker is Mdl 36, 7.5 HP, 3/60/230/460 volt, 1750 rpm. |
|
|
| 29222 | PULVERIZER | CARBON STEEL | 20 | Jacobson CS swing hammer pulverizer. Mdl ID-161B, SN 31913. 20 HP, 3/60/230/460 volt, 1750 rpm. Belt drive. 8" x 16" discharge. 2 3/4" side feed. |
|
|
| 29224 | PULVERIZER | CARBON STEEL | 20 | Jacobson CS swing hammer pulverizer. Mdl ID-161B, SN 31912. 20 HP, 3/60/230/460 volt, 1750 rpm. Belt drive. 8" x 16" discharge. 2 3/4" side feed. |
|
|
| 29225 | PULVERIZER | CARBON STEEL | 20 | Jacobson CS swing hammer pulverizer. Mdl ID-161B, SN 31758. 20 HP, 3/60/230/460 volt, 1750 rpm. Belt drive. 8" x 16" discharge. 2 3/4" side feed. |
|
|
| 30549 | PULVERIZER | CARBON STEEL | 75 | Mdl 35, Black Clawson wood chipper. SN 4070-75. W/16" x 16 1/2" feed opening w/base and 75 HP drive motor, 3/60/230/460 volt TEFC. |
|
|
| 30760 | PULVERIZER | CARBON STEEL | 33 | Alpine Superplex cool stream mill, CS. Mfd by Alpine (Germany), Mdl SUX800, SN 18462. Mill dia 800MM (32"). Rated 12-25KW motor, not included. Mill has (8) sets of (10) hammers, swing type mtd on the rotor. |
| 92 Items Returned | Go To Page: | 1 | 2 | 3 | 4 | 5 |
|
|
|
|
|
|
|
|