New search | Used INCINERATOR

7 Items Returned Go To Page: 1
		Stock Number	Product	Sub Group	Capacity	Description
Details Add to Quote		3055	INCINERATOR		1.4MM	Approx 835 cfm Trane Thermal fume incinerator. Mfd by Trane Thermal Co. System designed to incinerate combustible chemical fumes for air pollution compliance. Operated on DMA plant Emissions w/max content of 127 lb/hr Dimethyl ether, 9 lb/hr methanol and 27 lb/hr DMA dimethylaniline, incinerating "all organics in vent gases". Oil fired w/gas pilot. Unit skid mtd. Prepiped and prewired.
Details Add to Quote		17350	INCINERATOR		1	8,500 cfm vert brick lined CS fume incinerator. Mfd by Air Preheater. Main oxidation chamber measures 5' wide x 32' long x 14' high. CS construction w/refractory lining. Dual fuel gas and #6 oil. W/controls and burner.
Details Add to Quote		34423	INCINERATOR		21.0MM	21.0MM BTUH Trane Thermal chlorinated hydrocarbon incinerator w/waste heat recovery. Designed for various chemical solvents entrapped w/water. Max flow of water for incineration 1550 lb/hr. Unit is rated @ 21MM BTUH system consists of Trane Thermal horiz incinerator 6'6" dia x 15' long. Refractory lined. CS shell. Primarily fired on steam atomized #6 fuel oil. Maintaining a min temp of 2400 deg F. Burner is Trane Thermal LV-24 vortex burner. Firing 140 gph max, gas pilot ignition. Auxillary equipment for burner includes: FM insurance approved piping train for #6 fuel oil and waste. Waste piping is 316SS. Main combustion air fan is CS Spencer turbine rated 5,000 scfm @ 24 osig, powered by UL label 60 HP, 3/60/460 volt motor. ABCO elevated drum fire tube waste heat boiler. Single pass, 5'10" dia x 30' long x 13' high. Producing 10,000 lbs/hr @ 200 psig saturated steam. Feed water rate 250 psig-7650 lb/hr @ 220 deg F. Scrubber system is packed column 3'6" dia x 18'. CS shell lined w/Pyroflex and 4 1/2" acid brick. Ceramic intalux saddle packing. Stack is 12" dia x 10' high FRP. Quench air fan requires 30 HP motor (motor is missing). CS Garden City, designed temp 700 deg F. Pumps for scrubber system are duplexed 316SS Durco 5 HP, 3490 rpm. Remote control panel controls and meters. Boiler inlet temp, waste solvent feed rate, steam produced, scrubber exit temp, recycle air temp, incinerator chamber temp, boiler water level, feed water rate to boiler, liquid level in scrubber.
Details Add to Quote		203160	INCINERATOR		1619	1,619 ACFM, CS, Thermal Oxidizer system designed by Process Combustion with ABCO waste heat boiler, and Celicote scrubber system. ABCO waste heat boiler, Rated at 1750 Lbs/hr, NB# 3121, rated 250psi, 453 SqFt, built 1993, serial number 9301, model Waste Heat Firetube. With (49) 2.5" x 152" long tubes. Celicote final Scrubber, Model # SPT-24-84, Item # 16B, Rated for -6" WC to +12" WC, design temprature 180 degrees F, air flow capacity1,619 ACFM, material Dekrane 411.45. Preheat tube, Carbon Steel, 48" diameter by 196" long. Inlet 4" with a 11" outlet.
Details Add to Quote		210004	INCINERATOR		38537	48450 m3/hr (max) CS, Ecopure Regenerative Thermal Oxidizer, type RTOC3-3040, efficient exhaust gas purification system, manufactured by Durr Systems Gmbh, serial # 9377, order # 406-301-5, minimum flow volume 10,450 m3/hr, max pressure drop 6000 pa, combustion chamber temperature (regulator) 820 deg C, burner capacity 2 x 850 kw (max). Overall system data: Overall length of system 23344mm x 8284mm wide x 7490mm high, chimney stack height 13025mm, (3) RTO regenerator sectors, volumetric exhaust air flow, minimum 10450 Nm3/hr, average 47750 Nm3/hr, max 48450 Nm3/hr, exhaust air inlet temperature 20 deg C (nominal), Oxygen content in exhaust air 18% (min), exhaust air pressure at inlet to RTO system -5 mbar, quantity of pollutants in exhaust air 71 kg/hr (average), pollutant concentration 1.5 g/Nm3, net calorific value of pollutants approx 11.93 kWh/kg, exhaust preheating by ceramic heat exchanger approx 780 deg C, combustion chamber temperature 820 deg C, cleaned gas outlet temperature approx 68 deg C, Thermal reactor data: Reactor column 10120mm x 3620mm, sector 3260mm x 3620mm, column height 2130mm, layer height of ceramic honeycomb blocks 1.8m, sub-construction height 3670mm, distance between sectors 200mm, Combustion Chamber: Dimensions 10140mm long x 3480mm wide x 1690mm high, (2) gas burners each 850 kw (nominal) capacity, pre-pressure of natural gas 167 mbar, net calorific value of natural gas 10 kWh/Nm3, Air system: Process, purge, fresh, exhaust and crude air temperature approx 20 deg C, cleaned gas approx 68 deg C, cleaned gas fan volumetric flow 54000Nm3/hr nominal, 73780 m3/hr @ 100 deg C, speed 1665 rpm, total pressure difference 7730 pa, motor 200 kw, combustion air fan volumetric flow 3720 m3/hr, total pressure difference 8700 pa, motor 7.5 kw, 2880 rpm, purge air fan volumetric flow 2640 m3/hr, total pressure difference 3500 pa, motor 3.1 kw, 2830 rpm, Electrical equipment: Operating voltage 3 x 415 V, 50 Hz, burner, general control and motor valve voltage 240 V, 50 Hz, control I/O level, signal lamp, valve and interlocking voltage 24 V DC,
Details Add to Quote		211411	INCINERATOR		0	UNUSED Process Combustion thermal oxidizer, Model NPO-1192-28. Single burner design. With control panel. Mounts vertical. With unused burners, valves, controls, & blower package.
Details Add to Quote		214327	INCINERATOR			1800 degree F, John Zinc Thermal Oxidizer system, with waste heat boiler (IPP # 214326), Designed to incinerate various combinations fo solvent laden processing fumes. Serial Number 904756. System consists of a John Zink burner, Thermal Oxidizer/Incinerator, hot vent fan, combustion air fan, vent stack , and piperack mounted fuel gas and pilot gas traines. Natural gas is burned to bring the thermal oxidizer up to 1700 degrees F operating temperature. A retention time of one second is provided in the thermal oxidizer to convert the organic compounds to carbon dioxide, water vapor and sulfur dioxide. The incinerator is 6'6" ID x 21' long, 804 CuFt usable volume, lined with 4" of insulating castable. The burner has a carbon steel , center fired fuel gas gun. The vent stack is 4' OD x 50 ' high lined with 4" of insulating refractory. The control panel is mounted in the gas trane pipe rack and has a Nema 4 with air purge.