New search | Used KILN/CALCINER

14 Items Returned Go To Page: 1
		Stock Number	Product	Sub Group	Capacity	Description
Select		47096	KILN/CALCINER		24021	24" ID x 21' long, Bartlett Snow 304SS indirect fired rotary calciner. Shop number K3729. Has 15'6" heating area and 5'6" cooling section. Gas fired from underneath calciner tube. One section has (3) gas burners w/Pedcock feeders every 6"; 2nd section has (2) gas burners w/Pedcock feeders every 6". (63) total feeders. Burners run parallel to length of calciner. Tube has internal flights. Brick lined external shell. Mtd on (2) tires w/trunnions and driven by Girth gear w/chain to gearhead motor, 2 HP, 3/60/230/460 volt motor, 25 rpm output. Skid mtd design w/feed and discharge hoods. Mtd on skid is Nash L2 vac pump, direct driven by 5 HP, 3/60/220/440 volt motor.
Select		73480	KILN/CALCINER		1026	UNUSED 18.4" (460mm) dia x 26'3" (8000mm) long nickel (2.4068) calciner. Mfd by Plant and Equipment Eng (Germany), SN A27146, Type AG22/11/DK94-241, blt 1988. Heating zone 24" (600mm) wide, cooling zone 17'9" (5400mm) long. Tube driven by 1.5 KW, 3/50/380 volt motor. Calciner is electrically heated within a brick housing. Maximal allowable temps are: for the outer walls of the tube heating body 1652 deg F (900 deg C), for the heating chamber 1472 deg F (800 deg C), for the tube 752 deg F to 842 deg F (400 deg C to 450 deg C). Electrical heating capacity 5 KW. Tube speed 1-5 rpm.
Select		83298	KILN/CALCINER		99086	12'3" (3.74 meter) OD, (9'10" (3 meter) inside refractory) x 86' (26.3 meter) long CS direct fired rotary kiln. Rated capacity 3,300 ton/yr. Mfd by Babcock Krauss-Maffei. Temp 1200 deg C - 1300 deg C. Shell thickness 20mm, 114mm thick heat insulation lining and 250mm thick refractory. SS lifters and cast refractory lifters. Dual fuel (natural gas/oil) direct fired burners. Girth gear driven by variable speed drive, 1.48 rpm max. Unit has air driven emergency drive, .145 rpm max. Air supplied by diesel engine driven compressor. Kiln equipped w/on-board control panel used to sequence the actuation of the air injection valves and control the fans. Gas consumption kiln 6.6 cu meters/S, afterburner 3.8 cu meter/S. Steam fed via rotary coupling to manifolds mtd on outside of kiln shell and feed end. Controlled by remote operated valves which supply (7) zones along axis of shell.
Select		100191	KILN/CALCINER		36034	36" x 34', 316SS indirect fired calciner. Mfd by Industrial Furnace/Finch Mfg, Type reverse retort. 4-zone heating. Electrically heated. 3/60/480 volt. Electrical heating input 348 KW, max temp 1000 deg F. Octagonal shell. 3/8" wall thickness. Driven by TB Woods 5 HP DC adjustable speed motor thru gear reducer. Shell speed 0-5 rpm. Tire and trunnion mtd. W/feed and discharge assemblies.
Select		100192	KILN/CALCINER		36034	36" x 34', 316SS indirect fired calciner. Mfd by Industrial Furnace/Finch Mfg, Type reverse retort. 2.6MM BTU/hr input. 1300 deg F max temp. 4-zone heating. Gas fired Eclipse burner. Hexagonal shell. Tire and trunnion mtd. Shell driven by TB Woods 5 HP DC adjustable speed motor thru gear reducer. Screw feed driven by TB Woods 1 HP DC motor thru Dodge reducer w/SCR drive. W/Eclipse 7 1/2 HP blower, 70500 cfh.
Select		107682	KILN/CALCINER		18016	18" diameter x 16'8" long. 316LSS Renneburg Model #P77-106 rotary calciner. Has 6' long heating section and 5'6" long cooling section. Electric heated with tubular heating bars. Tire and trunnion mounted. Chain and sprocket driven by 3 HP, 3/60, 1750 rpm motor thru Cone 30:1 ratio right angle gear reducer. Has (2) 2,000 cfm @ 70 degree F exhaust fans, rated 2028 rpm, 3.57 brake HP.
Select		107686	KILN/CALCINER		36040	36" diameter x 40' long Bartlett Snow rotary calciner. Serial #81100. 316SS contacts. Indirect fired, Has (4) heating zones as follows: 7' long (65 KW), 9' long (25 KW), 6' long (25 KW), and 6' long (12 KW). 8' long cooling zone with external water spray nozzles. 40' is the overall cylinder length. 1st zone is for drying at 150-200 degree C; 9' zone is for heating at 350-360 degree C; the last 2-zones are for calcining at 350-360 degree C. Tire and trunnions mounted. Chain and sprocket driven.
Select		110548	KILN/CALCINER		14026	14" diameter x 26' long indirect fired, electrically heated, high nickel/Inconel tube calciner. Manufactured by CE Raymond, Serial #85051, Type #T50514, built 1986. 1800 degree F max. 12' long 4-zone heating section. Tire and trunnion mounted on (2) 10" diameter x 6" face tires and (2) 10" diameter x 4" face tires. Cylinder chain and sprocket driven by Reeves motodrive, 3 HP, 3/60/230/460 volt, 1800 rpm TEFC motor. Size 243, Z-configuration. Rated 4.85 to 48.5 output rpm. Has 316SS agitated screw feeder 3' long x 20" deep. Agitator and screw driven by 1/2 HP, 3/60/230/460 volt, 1800 rpm TEFC Reeves motordrive. Size 053. 8/4 to 84 rpm output. Has 3' cooling section with schedule 40 galvanized steel manifold and (3) full jet nozzles 3/8 G22. Discharge end of calciner has rotary airlock valve, manufactured by Prater Model #PAV-6-C, chain driven by 1/2 HP, 3/60/230/460 volt, 1800 rpm TEFC motor. 29 rpm output.
Select		207269	KILN/CALCINER		01006	6" ID diameter x 72" long Barlett-Snow Calciner, 1200 degrees F, with HH Alloy Tube, Manufactured by Bartlett-Snow-Pacific, Serial Number K5334. Skid mounted with the following overall dimensions: Length, 123" X width, 48" X height, 64". Heating area is 36" long with 4" insulation pack. Gas manifold contains seven jets, and is fed by a 3/4" inlet line. Heating chamber is exhausted by a 1 hp exhaust fan. Product hoppers and screw feed are 316 SS, inlet hopper is 8.5" X 11". Screw feed is 2" and driven by a 1/2 hp Browning motor. Calciner drive is by Seimens, 1750 rpm, and 2 hp.
Select		207372	KILN/CALCINER		0	600mm diameter x 13500mm long (approx.) Inconel 600/stainless steel indirect fired calciner, 250 kg/hr throughput, Manufactured by Riedhammer, Model DRA-8/60-E, serial # 85/4/039, Electrically heated by (4) 75 kw NiCr heating coils which are located underneath and at the side of rotary pipe, Max temperature 1150 deg C. heated pipe length 6.5m, brick lined kiln length 8m, total kiln length 15.5m, (3) regulation groups, connected load 300 kw, approx 175 kw energy consumption, kiln passage time 20-40 minutes, rotary tube in (3) section: 950mm s/steel section + 8300mm Inconel 600 section + 4300mm s/steel section, Inconel section only is heated, rotary tube is chain driven by 1.3 kw, 3/50/220/300/254/440 volt, 3475 rpm vari-speed geared motor, tube speed 0.25 to 3 rpm, kiln has a back-up diesel generator in case of power failure (keeps tube rotating to prevent deformation), complete unit mounted on c/steel frame with (4) legs (2 x legs have height adjustment), kiln is feed by approx 1.2m long x 100mm wide x 85mm deep s/steel vibratory conveyor with hopper, manufactured by JOST, type JD-50, 9.10 KG, 155 volt, 50 Hz, max temp 50 deg C, s/steel square design hopper 300mm wide x 300mm wide x 300mm straight side x 500mm high cone section, kiln discharges into a 500mm wide x 920mm long x 600mm deep s/steel hopper, with internal filter mesh and bottom mounted Spiroflow screw conveyor, conveyor with plastic tube and s/steel screw, 80mm diameter x approx 4m long, driven by an electric motor, conveyor with 100mm discharge, conveyor discharges into a 1 ton s/steel tote bin, 1m x 1m x 740mm deep, mounted on c/steel frame with castors, is also forkliftable, control panel is available.
Select		704184	KILN/CALCINER		1020	1' (304mm) ID x 20' (6087mm) direct gas fired CS rotary kiln. CS housing w/brick lining. Unit bull gear driven by 5.5 KW, 3/50/415 volt, 940 rpm non-flameproof motor via 49.2:1 ratio Renold gearbox. Unit with 6 1/2" dia x 52" long SS screw feeder, chain driven by .37 KW non-flameproof motor via 30.75:1 ratio reduction gearbox. Unit also w/(1) CS 7.5 KW fan; (1) 22" dia x 33" str side SS feed hopper w/fan; (1) 16" dia x 106" str side SS gas scrubber. Unit mtd on (2) trunnions.
Select		705341	KILN/CALCINER		1012	1'8" (530mm) inner diameter x 12'5" (3800mm) long, direct gas fired 304LSS rotary kiln. Manufactured by Nesa. Working capacity 500 kg/hr @ 850 degree C. Gas flow 250,000 Kcal/hr. 304LSS total length 15'9" (4800mm), 2'8" (810mm) outer diameter chamber with refractory brick lining. Unit bull gear driven by 0.5 - 5 rpm drive. Unit complete with 304LSS cyclone, (1) fan. Mounted on (2) trunnions.
Select		706261	KILN/CALCINER		1026	600mm inner diameter x 8.2m long high Nickel/Chrome indirect gas fired Calciner with 2-heating zones, manufactured by Selas, approx production capacity 300 kg/hr, max product temperature 1050-1150 deg C, material of feed & discharge sections Z15.CN.20/10, material of middle section Z12.NC.35/25, heating length 4.1m long, 33-gas burners, drum 630mm O/D, drum chain driven by Leroy Somer geared motor with 5.5 kw, 3/50/220-380 volt, 1435 rpm motor with type CB-E2-SB3, 31.8:1 ratio reduction gearbox, drum speed 1.25-10 rpm, drum with angle adjustment mechanism, drum mounted on 2-sets of 760mm diameter trunnion wheels, thrust bearings on drum tyres, drum with hammers, drum enclosed with steel outer casing insulated with shaped ceramic blocks, feed chute, gas regulation system for temperature control and automatic cut off, unit all mounted on c/steel frame, Calciner with (1) c/steel inclined discharge water cooled screw conveyor/cooler, 200mm wide x 4m long x 300mm deep, driven by Leroy Somer geared motor with 1.1 kw, 3/50/220-240-380-415 volt, 1420 rpm motor with a type CB-2504-SB3, 364.8:1 ratio gearbox, (1) ABB Solyvent-Ventec fan, type HD-73H-RO-ARGT-4-RT-12, driven by 11 kw, 3/50/380-415 volt, 2930-2945 rpm motor,
Select		706262	KILN/CALCINER		1026	600mm inner diameter x 8.2m long high Nickel/Chrome indirect gas fired Calciner with 2-heating zones, manufactured by Selas, approx production capacity 300 kg/hr, max product temperature 1050-1150 deg C, material of feed & discharge sections Z15.CN.20/10, material of middle section Z12.NC.35/25, heating length 4.1m long, 33-gas burners, drum 630mm O/D, drum chain driven by Leroy Somer geared motor with 2.2 kw, 3/50/220-380 volt, 1420-1435 rpm motor with type CB-2402-SB3, 31.5:1 ratio reduction gearbox, drum speed 1.25-10 rpm, drum with angle adjustment mechanism, drum mounted on 2-sets of 760mm diameter trunnion wheels, thrust bearings on drum tyres, drum with hammers, drum enclosed with steel outer casing insulated with shaped ceramic blocks, feed chute, gas regulation system for temperature control and automatic cut off, unit all mounted on c/steel frame, Calciner with (1) c/steel inclined discharge water cooled screw conveyor/cooler, 200mm wide x 4m long x 300mm deep, driven by Leroy Somer geared motor with 1.1 kw, 3/50/220-240-380-415 volt, 1420 rpm motor with a type CB-2504-SB3, 364.8:1 ratio gearbox, (1) ABB Solyvent-Ventec fan, type HD-73H-RO-ARGT-4-RT-12, driven by 11 kw, 3/50/380-415 volt, 2930-2945 rpm motor,